Automotive Tools

Wire Twist

DIGITAL AUDIO ON TWISTED PAIRS

I'm sure I don't have to tell you that the word is going digital.  And, in the audio-video space, the first to go digital was audio.  The Audio Engineering Society (AES) and the European Broadcast Union (EBU) worked on the first digital audio standards back in the 1980's, and the first standard, called AES3, came out in 1985, with continuing improvements until the present day.

 

Digital audio is a very different animal from analog audio. And, for the last twenty-five years, the forces of analog have been resisting the forces of digital audio.  Now there will probably always be those who will use analog, just like there are still people who ride horses. A horse may not be as fast as a car, but it is a lot more maneuverable, its pollution is a lot more eco-friendly, and there are still people making saddles.  In the same way, there will be analog microphones and mixers and tape machines made for a long time. The last of the large 24-channel multichannel professional machines, the Studer A827, was made in 2004. Smaller machines are still being made.

 

When digital first appeared there were many comments about the quality of the sound, especially compared to analog.  But, as digital has improved over the last decade or so, the analog crowd has grown smaller and smaller.  A lot of this is probably due to the MP3 and download crowd, who accept marginal quality as long as they get the content they want.  Compared to that quality, true AES digital audio is significantly higher quality.

 

So what is AES3 digital audio?  It is a system that allows the user to sample the analog material and turn it into digital audio (data).  Table 1 shows the most common sampling rates.

 

SAMPLING RATE

WHERE IS IT USED?

ACTUAL BANDWIDTH

44.1 kHz

Consumer digital, S/PDIF

5.6448 MHz

48 kHz

Broadcast radio/television

6.144 MHz

96 kHz

Film sound, recording studios

12.288 MHz

192 kHz

Top end, highest quality

24.576 MHz

 

Table 1

 

You will note that Table 1 starts at 44.1 kHz, the sampling rate for consumer CD's, digital audio track on consumer camcorders, and many other consumer applications. The quality of this sampling rate is considered to be slightly better than the performance of FM radio broadcasts.

 

 

 

The sampling rate is not the bandwidth of the signal running down the cable.  The bandwidth is determined by a number of factors.  First is the digital ‘word' size, the number of bits in each section of data.  The maximum allowed in the AES spec is 32-bit words.  The second factor is that the words can carry one or two channels of audio for every bit-stream.  This is why, for instance, on your home hi-fi receiver, it has a single RCA connector labeled "digital audio".  Than single connector will carry two channels of audio.  The final factor is that, for twisted pairs, the AES chose a system called ‘bi-phase' which mean, in the twisted pair, it doesn't matter which wire goes into which pin as long as you have the correct two wires going into the correct two pins.

 

What this all means is that you have to take the sampling rate and multiply it by 32 (word size) and again by 2 (2-channels) and again by 2 (bi-phase).  Or you can just multiply the sampling rate by 128 (32x2x2).  That formula will then tell you the bandwidth of the signal.  And, as you can see in Table 1, the actual signal bandwidth on a digital twisted pair, is way beyond the 20-20 kHz of analog audio.  In fact, it starts at almost 6 MHz. The AES committee soon realized that this bandwidth meant that the wavelength of even a consumer digital audio bitstream was easily reached as can be seen in Table 2.

 

SAMPLING RATE

BANDWIDTH

WAVELENGTH

QUARTER-WAVE

44.1 kHz

5.6448 MHz

53m

13m

48 kHz

6.144 MHz

49m

12m

96 kHz

12.288 MHz

24m

6m

192 kHz

24.576 MHz

12m

3m

 

Table 2

 

The committee realized that this mean they had to choose a specific impedance for these twisted pairs.  The ideal impedance, one with the lowest loss, would be 150Ω.  But this would make a huge cable, one that would never fit into an XLR (the desired connector).  So the AES committee reduced the effective distance and changed the impedance to get the size down to something much closer to the size designers and installers were used to in the old analog world.  And this impedance turned out to be 110Ω.

 

AES3 also spells out how far one can go on a given twisted pair.  If you feed an AES digital signal of 2 volts in, and a 0.2 volt (200 mV) signal out, that's as far as you can go.  This distance is also affected by the resistance (i.e. size) of the wires, so different gage wires will go different distances.  But since we're well within the quarter wavelength distance, the source, the cable, and the destination (load) impedance should all be 110Ω.  This is now a "transmission line" where we must match impedance.  Table 3 shows these distances.

GAGE

6 MHz

12MHz

25MHz

26 AWG

248m

193m

145m

24 AWG

337m

267m

198m

22 AWG

469m

381m

309m

 

Table 3

Table 3 might surprise a lot of people who were always told "digital audio signals can't go very far".  In some cases (if you read the previous installment on analog audio), these digital signals can go farther than analog audio signals!

 

You have a number of choices to run these digital signals.  Of course, there are AES twisted pairs.  But there are at least three variations on that theme aloe to choose from.  Then you have another standard AES3-id, that allows you to run these digital audio signals down coax cable.  We'll visit all of these….and more…in our next installment!

About the Author

Steve Lampen has been with Belden for 19 years and currently is Multimedia Technology Manager and Product Line Manager for Entertainment Products.  He has an FCC Lifetime General License (formerly an FCC First Phone License) and is a BICSI Registered Communications Distribution Designer. His latest book "The Audio-Video Cable Installer's Pocket Guide" is published by McGraw-Hill.

Visit our web site www.beldenapac.com or email us info@beldenapac.com

I have an old philip observation camera with only a piece of 2 pair twisted wire, can i connect it to an RCA?

I have an RCA input monitor how do i connect the two.
Regards,
William.

Not enough information to help. Is there a separate power supply or does power have to go through one of the two wires? Are there any markings on the camera - voltages, specs, even a model number?

5ive mics/ lil twist / snoop(wire)/ pac man jones/ dj don cannon/ young la /mitchelle'l